The TS-ETH100 is a PC/104 peripheral board (standard format) that provides a 10/100 Ethernet port. In addition, the TS-ETH100 provides an integrated 10/100 ethernet port through the ASIX AX88796B embedded MAC with on-chip PHY. It interfaces with the PC/104 connector via 16-bit data bus and the register map is NE2000 compatible.
2 Hardware Configuration
The TS-ETH100 jumpers select one-of-three IRQ lines and one-of-four I/O address regions. Also, it is possible to do PC/104 16-bit access using only the 64-pin PC/104 connector in ARM mode if the ARM jumper is ON. Jumpers IRQ5, IRQ6 and IRQ7 selects the desired ISA IRQ line for the TS-ETH100 MAC.
2.1 I/O Address
The PLD and MAC I/O address locations can be configured using jumpers Add1 and Add2 according to the table below:
|PLD I/O||MAC I/O||Add1||Add2|
2.2 Base Register Map
The TS-ETH100 has 4 registers of 4-bits each which appear implemented on the PLD.
|I/O Addr||Description||Data Access||Bits|
|Base+0x0||Board identifier||Read Only||returns 0x5 unique ID to verify presence|
|Base+0x4||PLD revision||Read Only||Returns PLD revision|
|Base+0x8||SRAM Control Register||Read Only||bit 3 = IRQ7 jumper status (1=ON, 0=OFF)
bit 2 = IRQ6 jumper status (1=ON, 0=OFF)
bit 1 = IRQ5 jumper status (1=ON, 0=OFF)
bit 0 = ARM jumper status (1=ON, 0=OFF)
|Base+0xC||PC104 Power Control||Bit 0 is RW||bit 3:1 = reserved
bit 0 = 5VDC power to PC/104 bus control
(0=power ON, 1=power OFF)
For a complete description of the MAC register map (which is NE2000 compatible), please refer to the ASIX AX88796B documentation.
3 Software Support
3.1 Loading the Module
The register map of ASIX AX88796B ethernet chip is NE2000 compatible, so driver support is straight-forward.
You can load the module like this:
modprobe ax88796b mem=0x200 irq=6 # Replace the irq option with your IRQ jumper configuration
If If you receive a message that the ax88796b module cannot be found then you will need to compile the module for your kernel.
You also may need to turn the pc104 adapter to pc104 mode as some boards default to a gpio state.
. /initrd/ts7800.subr # to load the pc104on function for the 7800 pc104on # to enable pc104
4 Product Notes
4.1 FCC Advisory
This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly (that is, in strict accordance with the manufacturer's instructions), may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A digital device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the owner will be required to correct the interference at his own expense.
If this equipment does cause interference, which can be determined by turning the unit on and off, the user is encouraged to try the following measures to correct the interference:
Reorient the receiving antenna. Relocate the unit with respect to the receiver. Plug the unit into a different outlet so that the unit and receiver are on different branch circuits. Ensure that mounting screws and connector attachment screws are tightly secured. Ensure that good quality, shielded, and grounded cables are used for all data communications. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The following booklets prepared by the Federal Communications Commission (FCC) may also prove helpful:
How to Identify and Resolve Radio-TV Interference Problems (Stock No. 004-000-000345-4) Interface Handbook (Stock No. 004-000-004505-7) These booklets may be purchased from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.
4.2 Limited Warranty
Technologic Systems warrants this product to be free of defects in material and workmanship for a period of one year from date of purchase. During this warranty period Technologic Systems will repair or replace the defective unit in accordance with the following process:
A copy of the original invoice must be included when returning the defective unit to Technologic Systems, Inc. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product.
This warranty is limited to the repair or replacement of the defective unit. In no event shall Technologic Systems be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product.
Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please, contact Technologic Systems to arrange for any repair service and to obtain repair charge information.