TS-8160-4200

From Technologic Systems Manuals
Revision as of 08:07, 24 February 2012 by Mark (talk | contribs) (→‎COM ports)
TS-8160-4200
TS-8160.jpg
Released Mar. 2011
Product Page
Documentation
Schematic
Mechanical Drawing

1 Overview

The TS-8160 is a TS-SOCKET baseboard that provides an upgrade path for Technologic Systems TS-7260 and TS-7800 products. This board accepts any TS-4xxx macrocontroller. It interfaces to the macrocontroller via two TS-SOCKET standard 100-pin connectors and brings out the various ports to industry standard connectors. The TS-8160 is compatible with the TS-ENC720 enclosure.

1.1 TS-4200

See the TS-4200 page for functionality regarding the CPU, FPGA, and OS.

TS-4200 Atmel AT91SAM9G20 400MHz ARM9

2 Getting Started

Before attempting to apply power to the baseboard, perform the following steps while taking proper static discharge precautions

  • Place the TS-8160 base board on a firm non-conductive surface.
  • Place the COM1 "Console Enable" jumper in the console position so the debug port is brought out to the DB9 and COM1 headers.
  • Carefully, insert the macrocontroller daughterboard by aligning and pressing evenly and firmly onto the pair of mating connectors
  • Connect the console serial terminal cable
  • Connect the Ethernet cable is applicable.
  • Apply power
  • Monitor the TS-SOCKET SBC using a terminal emulator connected to the serial console port to verify that the board is operating properly

See the TS-4200 page for more details on dealing with the functionality of the macrocontroller.

3 Features

3.1 DIO header

The DIO is manipulated through tsctl, or through manipulation of the registers directly.

Using tsctl will be the easiest way to communicate with the IO. This example will show the simplest way to toggle the IO, but see the tsctl page for more advanced usage.

# Start tsctl server if it is not already running.
# This only needs to be done once
tsctl --server &

# Lookup the logical DIO mapping of the dio header pin 1
eval `tsctl 127.0.0.1 System MapLookup DIO_1`
# If you run this outside of the eval it will return:
# DIO_1=130 

# Toggle the DIO high and low:
tsctl 127.0.0.1 DIO Set $DIO_1 high
tsctl 127.0.0.1 DIO Set $DIO_1 low
Pinout Header
Pin Name Notes
1 DIO_1 Pulled high by R124
2 Ground
3 DIO_3 Pulled high by R123
4 I2C_CLK See TS-4200#I2C for more details.
5 DIO_5 Pulled high by R122
6 SPI_CS# See TS-4200#SPI for more details.
7 DIO_7 pulled high by R121
8 I2C_DAT See TS-4200#I2C for more details.
9 DIO_9 Pulled high by R120
10 SPI_MISO See TS-4200#SPI for more details.
11 DIO_11 Pulled high by R119
12 SPI_MOSI See TS-4200#SPI for more details.
13 DIO_13 Pulled high by R118
14 SPI_CLK See TS-4200#SPI for more details.
15 DIO_15 Pulled high by R117
16 CPU_3.3V Do not draw more than 12mA
16 15
14 13
12 11
10 9
8 7
6 5
4 3
2 1
WARNING: DIO are not 5V tolerant. Only SPI_MOSI on this header is 5V tolerant.

3.2 LCD Header

The LCD header is designed around compatibility with our low cost LCD-LED: Alphanumeric 2x24 LCD. These IO are manipulated through tsctl, or through manipulation of the registers directly. Connector CN8 is a 14 pin (2x7) 0.1" spacing header.

Pinout Header
Pin Name Notes
1 LCD_5V Provides up to 1400mA
2 Ground
3 LCD_RS
4 LCD_BIAS
5 LCD_EN
6 LCD_WR#
7 LCD_D1
8 LCD_D0
9 LCD_D3
10 LCD_D2
11 LCD_D5
12 LCD_D4
13 LCD_D7
14 LCD_D6
14 13
12 11
10 9
8 7
6 5
4 3
2 1
WARNING: LCD_D0 thru LCD_D7 are 5V tolerant. LCD_WR#, LCD_RS, and LCD_EN are not.

Power to the LCD header can be toggled by manipulating LCD Enable in the #Register Map. The LCD_5V pin can provide up to 1400mA, but this is a shared 5V rail and will depend on your power supply and what other devices are using that rail.

3.3 ADC Header

The Analog to Digital Converter consists of a 4-channel 16 bit sigma-delta converter and two, 2-channel analog switches. These are configured to allow input and conversion on two differential channels and 4 single ended channels. The 6-channel Analog to Digital signals are contained on connector HD5 which is a 16 pin (2x8) 0.1" spacing header. The connector layout and the signals carried by each pin are defined below. The input range for the differential input channels is 0- 2 VDC, and the input range on the single-ended channel is nominally 0-10 VDC.

This can be accessed on the TS-4200 by using the TS-4200#ADC Core.

Pinout Header
Pin Type Signal
1 Single ended Channel 6
2 N/A GND
3 Single ended Channel 5
4 N/A GND
5 Single ended Channel 4
6 N/A GND
7 Single ended Channel 3
8 N/A GND
9 N/A Not connected
10 N/A GND
11 Differential Channel 2-
12 Differential Channel 2+
13 N/A GND
14 Differential Channel 1-
15 Differential Channel 1+
16 N/A GND
16 15
14 13
12 11
10 9
8 7
6 5
4 3
2 1


3.4 Sleep mode

The TS-8160 features a AVR that has the ability to cut power to the macrocontroller for a specified amount of time. You can also use the jumper labelled 'WAKE', or the press the button on SW1 to restore power to the macrocontroller.

The ts8160ctl is available here.

Sleeping the board is essentially a shutdown. It is recommended that you have all of your filesystems in a read only state before running this command to avoid disk corruption. This example will simply shut down the macrocontroller for 20 seconds.

ts8160ctl --sleep 20

Power consumption during sleep mode is approximately 100uA.

Note: Sleep times will be rounded up to the granularity of sleep, which is 8 seconds for sleeps under ~3 days and 2048 seconds for longer sleeps. Actual sleep time will be +/- 10% the requested time due to low-power oscillator variation.

3.5 COM ports

Port Type RX (or 485 +) TX (or 485 -) Notes
ttyS0 RS232 DB9 pin 2, COM1 header pin 2 DB9 pin 3, COM1 header pin 3 Only with console enable jumper on
ttyS1 RS485 DB9 pin 1, COM1 header pin 1 DB9 pin 6, COM1 header pin 6
ttyS2 RS232 DB9 pin 2, COM1 header pin 2 DB9 pin 3, COM1 header pin 3 Only with console enable jumper off
ttyS3 RS232 DB9 pin 8, COM1 header pin 8 DB9 pin 7, COM1 header pin 7
ttyS4 RS232 COM2 header pin 2 COM2 header pin 3
ttyS5 RS485 COM2 header pin 1 COM2 header pin 6
ttyS6 RS232 COM3 header pin 2 COM3 header pin 3 CTS available on pin 8

3.6 PC104 Header

The PC-104 connector consists of two rows of pins labeled A and B, the numbering of of which is shown below. The signals for the PC-104 are generated by the MAX240 PLD located on the baseboard. It converts the MUXBUS signals from the dual 100-pin Macrocontroller interface bus. Pin A1 is nearest to the macrocontroller mounting hole.

See the TS-4200#PC104 section for more details on working with the PC104 bus.

Any of the IO on this board labelled DIO_ can be controlled through tsctl as PC104_A/B<pin>, or through manipulation of the registers directly.

# Start tsctl server if it is not already running.
# This only needs to be done once
tsctl --server &

# Lookup the logical DIO mapping of the PC104 header pin A16
eval `tsctl 127.0.0.1 System MapLookup PC104_A16`
# If you run this outside of the eval it will return:
# PC104_A16=138

# Toggle the DIO high and low:
tsctl 127.0.0.1 DIO Set $PC104_A16 high
tsctl 127.0.0.1 DIO Set $PC104_A16 low

You can also drive these DIO to manually manipulate the PC104 address to make peripherals usable that require a higher range of address than provided by the default address space of the MUXBUS.

Pin Name Pin Name
A1 BUS_BHE# B1 Ground
A2 AD_07 B2 ISA_RESET
A3 AD_06 B3 5V
A4 AD_05 B4 AD_08
A5 AD_04 B5 CPU_3.3V
A6 AD_03 B6 Not connected
A7 AD_02 B7 Not connected
A8 AD_01 B8 Not connected
A9 AD_D0 B9 VIN
A10 ISA_WAIT# B10 Ground
A11 Ground B11 DIO_B11
A12 Not connected B12 DIO_B12
A13 Not connected B13 ISA_LOW#
A14 Not connected B14 ISA_IOR#
A15 Not connected B15 Not connected
A16 DIO_A16 B16 Not connected
A17 DIO_A17 B17 AD_09
A18 DIO_A18 B18 AD_10
A19 DIO_A19 B19 Not connected
A20 DIO_A20 B20 AD_12
A21 DIO_A21 B21 ISA_IRQ7
A22 ISA_ADD9 B22 ISA_IRQ6
A23 ISA_ADD8 B23 ISA_IRQ5
A24 ISA_ADD7 B24 Ground
A25 ISA_ADD6 B25 AD_11
A26 ISA_ADD5 B26 AD_13
A27 ISA_ADD4 B27 AD_14
A28 ISA_ADD3 B28 AD_15
A29 ISA_ADD2 B29 5V
A30 ISA_ADD1 B30 ISA 14.3 MHZ
A31 ISA_ADD0 B31 Ground
A32 Ground B32 Ground
WARNING: Most of the pins on the PC104 bus are only 3.3V tolerant. Refer to the schematic for more details.

4 Register Map

All of these registers are intended for 16 bit access. You can find this range at 0x30000400. You must first set the MUXBUS configuration register before accessing this range. For example, to read the board ID:

peekpoke 16 0x30000020 0x181 # Set MUXBUS configuration
peekpoke 16 0x30000400 # Read Board ID register (0x0)
Offset Bits Name Access Description
0x0 15:0 Board ID Read Only Returns '0x8100'
0x2 3:0 PLD revision Read Only
7:4 LCD Contrast Read/Write
8 USB Reset Read/Write Allows you to reset the USB hub
9 ISA Reset Read/Write
10 Enable Oscillator Read/Write
11 Enable RS-232 Read/Write
12 Enable LCD Power Read/Write
13 CAN1 Standby Read/Write
14 CAN2 Standby Read/Write
15 LCD Contrast Enable Read/Write
0x4 7:0 Odd numbered pins 15:1 Read/Write Output data on the DIO header
13:8 PC104 pins A21:A16 Read/Write Output data on PC104 header
15:14 PC104 pins B12:B11 Read/Write Output data on PC104 header
0x6 7:0 Pins 14-7 data Read Only LCD data lines output data
8 LCD Write/Read (pin 6) Read/Write LCD Header pin 6 output data
9 LCD Register Select (pin 3) Read/Write LCD Header pin 3 output data
10 LCD Enable (pin 5) Read/Write LCD Header pin 5 output data
11 AVR MOSI Read/Write
12 AVR SCLK Read/Write
13 AVR RESET Read/Write
14:15 Reserved N/A
0x8 7:0 DIO data direction (odd pins 15:1) Read/Write DIO Header data direction
13:8 PC104 pins A21:A16 Read/Write PC104 GPIO data direction
15:14 PC104 pins B12:B11 Read/Write PC104 GPIO data direction
0xa 7:0 Pins 14-7 direction Read Only LCD GPIO data direction
8 LCD Write/Read (pin 6) Read/Write LCD Header pin 6 data direction
9 LCD Register Select (pin 3) Read/Write LCD Header pin 3 data direction
10 LCD Enable (pin 5) Read/Write LCD Header pin 5 data direction
0xc 7:0 DIO Input Data (odd pins 15:1) Read/Write DIO Header input data
13:8 PC104 pins A21:A16 Read/Write PC104 GPIO input data
15:14 PC104 pins B12:B11 Read/Write PC104 GPIO input data
0xe 7:0 Pins 14-7 data Read Only LCD Header input data
8 LCD Write/Read (pin 6) Read/Write For selecting between reads/writes
9 LCD Register Select (pin 3) Read/Write Select between data and instruction registers
10 LCD Enable (pin 5) Read/Write Toggles the LCD functionality
11 AVR MISO Read/Write
15:12 Reserved N/A

5 Product Notes

5.1 FCC Advisory

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly (that is, in strict accordance with the manufacturer's instructions), may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A digital device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the owner will be required to correct the interference at his own expense.

If this equipment does cause interference, which can be determined by turning the unit on and off, the user is encouraged to try the following measures to correct the interference:

Reorient the receiving antenna. Relocate the unit with respect to the receiver. Plug the unit into a different outlet so that the unit and receiver are on different branch circuits. Ensure that mounting screws and connector attachment screws are tightly secured. Ensure that good quality, shielded, and grounded cables are used for all data communications. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The following booklets prepared by the Federal Communications Commission (FCC) may also prove helpful:

How to Identify and Resolve Radio-TV Interference Problems (Stock No. 004-000-000345-4) Interface Handbook (Stock No. 004-000-004505-7) These booklets may be purchased from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.

5.2 Limited Warranty

Technologic Systems warrants this product to be free of defects in material and workmanship for a period of one year from date of purchase. During this warranty period Technologic Systems will repair or replace the defective unit in accordance with the following process:

A copy of the original invoice must be included when returning the defective unit to Technologic Systems, Inc. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product.

This warranty is limited to the repair or replacement of the defective unit. In no event shall Technologic Systems be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product.

Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please, contact Technologic Systems to arrange for any repair service and to obtain repair charge information.