Difference between revisions of "TS-SER4"

From Technologic Systems Manuals
(Created page with "{{Infobox |title = TS-SER4 |image = 300px |titlestyle = |headerstyle = background:#ccf; |labelstyle = width:33% |datastyle = |data1 ...")
Line 135: Line 135:
| Disabled
| Disabled
= X1 and Non-standard Baud Rates =
The TS-SER4 has a socket for a 5V 8-DIP, 4 Leads (half size, metal can) oscillator.  By default, the TS-SER4 uses a clock (1.8432MHz) from the PC104 bus which has a maximum baud rate of 115200.  When a signal is detected on the X1 socket, it will use the clock from there instead.
= Product Notes =
== FCC Advisory ==
{{:FCC Advisory Statement}}
== Limited Warranty ==
{{:Limited Warranty}}

Revision as of 14:03, 19 December 2011

Product Page
Mechanical Drawing

1 Overview

The TS-SER4 is a PC/104 expansion card with four serial ports using the PC standard 16C550 type UARTs (with 16-byte FIFOs). All four COM ports support RS-232 levels and two of these COM ports can optionally support RS-422/ RS-485 levels.

A flexible interrupt sharing design allows for a large number of COM ports using a minimum number of interrupts. An interrupt status register allows rapid identification of the interrupt source.

This product uses a multi-layer PCB with power and ground planes to minimize noise and EMI issues. The TS-SER4 only requires a single 5V power supply.

2 Getting Started

See your SBC's PC104 section for information on the ISA 16550 driver and getting a connection to the COM device.

3 Serial Ports

The two serial ports that are labeled COM_A and COM_B support RS-232 levels only. The two serial ports labeled COM_C and COM_D support a subset of RS-232C handshakes lines that is sufficient for the vast majority of applications. In addition these two ports can optionally have RS-485/RS-422 drivers. The table below shows these ports.

4 COM/IO Selection

On On On 2e8 3e8
On Off On 2f8 3f8
Off On On 260 268
Off Off On Disabled Disabled
On On Off 250 258
On Off Off 220 228
Off On Off 210 218
Off Off Off Disabled Disabled
Note: JP18 is shared with the parallel port

5 Parallel Port

The parallel port is a standard PS/2 mode bidirectional port. It can be assigned to 5 different I/O locations or disabled completely. The parallel port can use interrupts 7 and 9. To select the desired interrupt, simply install a jumper on the associated pins in the IRQ jumper block.

JP16 JP17 JP18 LPT Address
On On On 278
On Off On 378
Off On On 3bc
Off Off On Disabled
On On Off 278
On Off Off 27c
Off On Off 37c
Off Off Off Disabled

6 X1 and Non-standard Baud Rates

The TS-SER4 has a socket for a 5V 8-DIP, 4 Leads (half size, metal can) oscillator. By default, the TS-SER4 uses a clock (1.8432MHz) from the PC104 bus which has a maximum baud rate of 115200. When a signal is detected on the X1 socket, it will use the clock from there instead.

7 Product Notes

7.1 FCC Advisory

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly (that is, in strict accordance with the manufacturer's instructions), may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A digital device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the owner will be required to correct the interference at his own expense.

If this equipment does cause interference, which can be determined by turning the unit on and off, the user is encouraged to try the following measures to correct the interference:

Reorient the receiving antenna. Relocate the unit with respect to the receiver. Plug the unit into a different outlet so that the unit and receiver are on different branch circuits. Ensure that mounting screws and connector attachment screws are tightly secured. Ensure that good quality, shielded, and grounded cables are used for all data communications. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The following booklets prepared by the Federal Communications Commission (FCC) may also prove helpful:

How to Identify and Resolve Radio-TV Interference Problems (Stock No. 004-000-000345-4) Interface Handbook (Stock No. 004-000-004505-7) These booklets may be purchased from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.

7.2 Limited Warranty

Technologic Systems warrants this product to be free of defects in material and workmanship for a period of one year from date of purchase. During this warranty period Technologic Systems will repair or replace the defective unit in accordance with the following process:

A copy of the original invoice must be included when returning the defective unit to Technologic Systems, Inc. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product.

This warranty is limited to the repair or replacement of the defective unit. In no event shall Technologic Systems be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product.

Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please, contact Technologic Systems to arrange for any repair service and to obtain repair charge information.